| |
|
|
 |
 |
 |
 |
| General
Gunsmithing Price Effective 01/01/08 (Prices Subject to change without notice) |
| |
|
| Hourly Service Charge (Man Hour) |
$50.00 |
| Hourly Service Charge (Man/Machine) |
$65.00 |
| Minimum Charge Per Gun |
$30.00 |
| Written Estimate ( If No Work Is Done) |
$65.00 |
| Clean & Oil Gun |
$50.00 & Up |
| Barrel &
Action Work |
| Labor Only |
| Chamber and fit barrel to action |
$200.00 |
| Install Muzzle Brake (Plus Cost of
Muzzlebrake) |
$110.00 |
| Make Chamber Cast |
$50.00 |
| Contour front and rear receiver ring |
$50.00 & up |
| Cut and crown rifle barrel |
$50.00 |
| Remove live round from chamber |
$50.00 |
| Remove fired case from chamber |
$30.00 & up |
| Check firing pin protrusion |
$30.00 |
| Forge bolt handle |
$75.00 |
| Check headspace | $30.00 |
| Lap barrel |
$70.00 |
| Lap bolt lugs-does not include setting
back barrel |
$65.00 |
| Install barrel liner-does not include cost
of liner or rebluing |
$100.00 |
| Remove live round |
$35.00 & up |
| Remove obstruction from bore |
$50.00&UP |
| Install prethreaded and short chambered
barrel (Bluing Extra) |
$150.00 |
| Install safety |
$50.00 & up |
| Straighten barrel ( Rifle and/or Shotgun) |
$60.00 & up |
| Install trigger |
$50 & up |
| Weld on new bolt handle |
$65.00 |
| Handgun Work |
| Labor Only |
| |
|
| Trigger job- clean & smooth |
$65.00 |
| Rebarrel handgun with factory barrel |
$75.00 & up |
| Install beavertail grip safety |
$75.00 |
| Set timing |
$100.00 |
| Bob hammer spur |
$50.00 |
| |
|
| Chamfer revolver barrel |
$40.00 |
| |
|
| Chamfer revolver cylinder |
$50.00 |
| |
|
| |
|
| Straighten revolver crane |
$50.00 & up |
| Open port ejection |
$60.00 |
| Install crane lock |
$60.00 |
| Remove/modify revolver hammer spur |
$50.00 |
| Bevel magazine well |
$50.00 |
| Rebarrel |
$50.00 & up |
| |
|
| Action job ( completely hone
& smooth all parts ) |
$100.00 & up |
| Shotgun Work |
| Labor Only |
| Cut long forcing cone in plated barrel |
$75.00 |
| Raise dent in barrel |
$50.00 & up |
| Make new hinge pin |
$75.00 & up |
| Polish bore & chamber |
$50.00 |
| Port barrel |
$75.00 & up |
| Resoder forend lug ( bluing not included ) |
$75.00 |
| Resoder rib ( bluing not included ) |
$80.00 & up |
| Install screw in chokes ( 3 standard tubes ) |
$125.00 |
| Sight Work |
| Labor Only |
| Sight in plus ammo (Standard )
Computer assisted sightin |
$25.00 |
|
Magnums Muzzleloader |
$30.00 $35.00 |
| Pattern Shotgun plus ammo |
$40.00 |
| Install sight bead on shotgun (Drill and tap,
standard bead included) |
$25.00 |
| Install insert in pistol sight |
$45.00 |
| Cut dovetail in barrel |
$60.00 |
| Drill & tap barrel or receiver for sights
per hole |
$15.00 |
| Install receiver sights-gun drilled &
tapped |
$45.00 |
| Install scope and mounts & sight
in W/Customer's ammo |
$60.00 |
| Install scope and mounts-gun not drilled
& tapped |
$110.00 |
| Install screw-on type sight ramp |
$40.00 |
| Install sweat-on type sight ramp |
$50.00 |
| Stock Work |
| Labor Only |
| Glass bed rifle (Action ONLY) |
$95.00 |
| Glass bed match or target rifle |
$125.00 |
| Pillar bed |
$95.00 |
| Fit & bed barreled action in fiberglass
stock |
$85.00 & up |
| Inlet & finish semi inletted stock |
$375.00 & up |
| Custom stock from blank |
$600.00 & up |
| Refinish stock- unfilled |
$75.00 |
| Refinish stock-(polyurathane oil spray) |
$125.00 |
| Install recoil pad |
$40.00 |
| Install standard sling swivels |
$25.00 |
| Recoil reducer |
$25.00 to $75.00 |
| Metal Refinishing
Shotgun |
| Labor Only |
| Pump & auto (Rem 870, 1187 & like
models ) |
$165.00 |
| Browning A-5, Winchester 12,& like models |
$225.00 |
| Models with aluminum receivers ( Mos 500, Win
1200 & like models) |
$100 & up |
| Over Under & Side by Side ( refinishing
aluminum receiver $50.00 extra) |
$375.00 |
| There will be an Extra Charge
for Rusted and Pitted |
|
| Shotgun barrels only |
|
| Plain |
$75.00 |
| Vent rib |
$95.00 |
| Over/ Under & Side by Side |
$250.00 & up |
| Metal Refinishing
Handgun |
| Labor Only |
| Revolvers |
|
| Small |
$150.00 |
| Medium |
$175.00 |
| Large |
$200.00 |
| Autos |
$165.00 |
| Frame or slides only |
$95.00 |
| Metal Refinishing
Rifles |
| Labor Only |
| Most lever actions |
$150.00 & up |
| Bolt actions |
$150.00 |
| Pumps & Auto - all steel |
$175.00 & up |
| Remington 7400 |
$150.00 |
| Models with aluminum receivers ( steel part
only ) |
$125.00 |
| Aluminum receiver add |
$85.00 |
| Teflon Type
Refinishing |
| Labor Only |
| Bolt ActionRifle complete |
$175.00 |
| Shotguns & Semi auto rifles complete |
$175.00 |
| Pistols & Revolvers complete |
$135.00 |
| |
| |
| |
|
| |
|
| Gold plate small parts ( trigger, hammer, ect
)per part |
$35.00 |
| Case Color ( receiver, frame,
ect ) |
$250.00 & up |
